43-1701.fm Page 1 Wednesday, September 20, 2000 8:48 AM
2-Line 900 MHz Handsfree
Cordless Phone
43-1701.fm Page 3 Wednesday, September 20, 2000 8:48 AM
WARNING:
To reduce the risk of fire or
shock hazard, do not expose this product to rain
or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con-
stitute a risk of electric shock. Do
not open the product’s case.
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accom-
panying this product.
!
Your phone is ETL listed to UL standards and meets all applica-
ble FCC standards.
3
Contents
43-1701.fm Page 4 Wednesday, September 20, 2000 8:48 AM
READ THIS BEFORE INSTALLATION
Each device that you connect to the phone line draws power
from the phone line. We refer to this power draw as the device’s
ringer equivalence number, or REN. The REN is on the bottom
of the base.
If you are using more than one phone or other device on the
line, add up all the RENs. If the total is more than five (three in
rural areas), your phone might not ring. If ringer operation is im-
paired, remove a device from the line.
FCC STATEMENT
This telephone complies with Part 68 of FCC Rules. You must,
upon request, provide the FCC registration number and the
REN to your phone company. These numbers are on the bot-
tom of the base.
Note:
You must not connect your phone to any of the following
coin-operated systems, party-line systems, or most electronic
key phone systems.
In the unlikely event that your phone causes problems on the
phone line, the phone company can temporarily discontinue
your service. If this happens, the phone company attempts to
notify you in advance. If advance notice is not practical, the
phone company notifies you as soon as possible and advises
you of your right to file a complaint with the FCC.
Also, the phone company can make changes to its lines, equip-
ment, operations, or procedures that could affect the operation
of this telephone. The telephone company notifies you of these
4
Contents
43-1701.fm Page 5 Wednesday, September 20, 2000 8:48 AM
changes in advances, so you can take the necessary steps to
prevent interruption of your telephone service.
This equipment complies with the limits for a Class B digital de-
vice as specified in Part 15 of FCC Rules. These limits provide
reasonable protection against radio and TV interference in a
residential area. However, your equipment might cause TV or
radio interference even when it is operating properly. To elimi-
nate interference, you can try one or more of the following cor-
rective measures.
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the radio
or TV.
• Use outlets on different electrical circuits for the equipment
and the radio or TV.
Consult your local RadioShack store if the problem still exists.
Warning:
Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
5
Contents
43-1701.fm Page 6 Wednesday, September 20, 2000 8:48 AM
ˆ Features
Your RadioShack 2-Line 900 MHz Handsfree Cordless Phone
combines the clarity of 900 MHz communication with portability
and convenience. The phone’s cordless keypad clips to your
belt or clothing so you can make and answer calls away from
the unit’s base. The headset allows you to use your hands while
you talk.
10-Memory Speed Dial
— stores up to 10 frequently-called
phone numbers for easy dialing.
Ring/Vibrate Dual Mode Selection
— lets you set the ringer to
ring, vibrate, or both.
Receiver Volume Control
— lets you adjust the volume you
hear during a call.
Ample Talk and Standby Time
— when fully charged (about
12 hours), the supplied battery provides about 7 hours of talk
time or 7 days of standby time.
10-Channel Auto Scan
— automatically selects a clear chan-
nel when you make or answer a call.
Conference
— lets you talk to parties on both lines at the same
time.
Security Access-Protection Code
— prevents other cordless
phone users from using your phone line.
Hearing-Aid Compatible —
lets you use your phone with hear-
ing-aids that have a T (telephone) switch.
6
Features
43-1701.fm Page 7 Wednesday, September 20, 2000 8:48 AM
ˆ A Quick Look at the Phone
LOW BATT
VOLUME
VOLUME
8
9
HOLD
CONF
L1
L2
DC
Jack
TELLINE
1/2
TELLINE
2
CHANNEL
MUTE
REDIAL/
PAUSE
FLASH
MEMORY
RING VIB/
RING/VIB
ˆ Preparation
SELECTING A LOCATION
You can place the phone’s base on a flat surface such as a
desk, shelf, or table. Select a location that is:
• near an easily accessible AC outlet
7
Preparation
43-1701.fm Page 8 Wednesday, September 20, 2000 8:48 AM
• near a telephone line jack
• out of the way of normal activities
• away from electrical machinery, electrical appliances, metal
walls, filing cabinets, wireless intercoms, security alarms,
and room monitors
The base’s location affects the phone’s range. If you have a
choice of several locations, try each to see which provides the
best performance.
Notes:
• Your telephone is designed to be connected to the tele-
phone network using a compatible modular jack that is Part
68 compliant.
• Your telephone connects directly to a modular telephone
line jack. If your phone line jack is not a modular jack, you
can update the wiring yourself, using jacks and adapters
available at your local RadioShack store. Or, you can let
the phone company update the wiring for you.
• The USOC number of the jack to be installed is RJ14C (for
TEL LINE 1/2
) or RJ11C (for both telephone line jacks).
CONNECTING THE BASE
You can power the base using the supplied 15V, 300-mA AC
adapter.
8
Preparation
43-1701.fm Page 9 Wednesday, September 20, 2000 8:48 AM
Cautions:
You must use a Class 2 power source that supplies
15V DC and delivers at least 300 mA. Its center tip
must be set to positive and its plug must fit the
phone's 15V 300 mA jack. Using an adapter that does not
meet these specifications could damage the phone or the
adapter.
!
• Always connect the AC adapter to the phone before you con-
nect it to AC power. When you finish, disconnect the adapter
from AC power before you disconnect it from the phone.
1. If you have a RJ14C modular telephone line jack for 2 line
usage, plug one end of the supplied 4-pin modular cord into
TEL LINE 1/2
. Then plug the other end into the RJ14C mod-
ular phone line jack.
If you have two RJ11C modular telephone line jacks for
using 2 lines, plug one end of the supplied 4–pin modular
TEL LINE 1/2
cord into
, and one end of the supplied 2–pin
TEL LINE 2
modular cord into
. Then plug the modular cords’
other ends into the RJ11C modular phone line jacks.
2. Lift the base’s antenna to a vertical position.
CONNECTING AND CHARGING THE
BATTERY PACK
The phone comes with two rechargeable nickel-cadmium bat-
tery packs. You must connect the battery pack and charge it for
at least 12 hours for the first time before you use the phone.
9
Preparation
43-1701.fm Page 10 Wednesday, September 20, 2000 8:48 AM
To connect the battery pack, line up
the slots on the battery pack with
the posts on the back of the keypad.
Press down and slide the battery
pack forward until the latch clicks.
Battery
Pack
Battery
Charging
Slot
To charge the battery
pack, place the keypad in
the base’s front charging
slot. The CHARGE indica-
tor at the front of the unit
lights.
Antenna
CHARGE
Keypad
Charging
Slot
L1
L2
To charge the spare bat-
tery pack, place it in the
rear charging slot with its
latch end facing down and
CHARGE
PAGE
its contacts toward the rear of the base. The CHARGE indicator
between the two slots lights.
Notes:
• Recharge the battery pack anytime the LOW BATT indica-
tor flashes, or if the keypad beeps while you are on the
phone.
• When you first use the phone after charging or recharging
the battery pack, the phone might not work. Return the key-
pad to the base for about 5 seconds to reset the security
access-protection code.
• About once a month, fully discharge the battery pack by
keeping the phone off the base until the LOW BATT indica-
tor flashes, or if the keypad beeps while you are on the
10
Preparation
43-1701.fm Page 11 Wednesday, September 20, 2000 8:48 AM
phone. Otherwise, the battery pack loses its ability to fully
recharge.
• If the front CHARGE indicator does not light when you
place the keypad on the base, be sure the battery pack and
AC adapter are correctly and securely connected. Also,
check the charging contacts on the keypad and base. If the
contacts are dirty or tarnished, clean them with a pencil
eraser.
• If the battery pack becomes completely discharged or the
base loses power while the keypad is away from it, place
the keypad on the base for about 5 seconds to reset the
security access protection code. If the keypad loses power,
leave it on the base to charge the battery pack.
• If you are not going to use your phone for an extended
period of time, disconnect its battery pack. This helps
increase the battery pack’s usable life.
Recharging the Battery Pack
The battery pack should last about a year. If the battery pack
does not hold a charge for more than 2 hours after an overnight
charge, replace it. You can order a replacement battery pack
through your local RadioShack store.
Note:
To avoid losing numbers stored in memory, you must in-
stall and begin charging the new battery pack within 2 minutes
of removing the old one.
1. To remove the old battery pack, press the latch release,
then slide the battery pack off the keypad.
11
Preparation
43-1701.fm Page 12 Wednesday, September 20, 2000 8:48 AM
2. To connect the new battery pack, line up the slots on the
battery pack with the posts on the keypad, then press down
and slide it forward until the latch clicks.
3. Charge the battery pack for 12 hours before using it.
Cautions:
• Be careful not to short the battery pack by touching it with
conducting materials, such as rings, bracelets, and keys.
The battery pack or conductor might overheat and burn.
• Do not dispose of the battery pack in a fire because it might
explode.
• Do not open or mutilate the battery pack.
Note:
If you have trouble replacing the battery pack, take the
phone to your local RadioShack store for assistance.
®
Important:
The EPA certified RBRC Battery Re-
cycling Seal on the nickel-cadmium (Ni-Cd) bat-
tery indicates RadioShack is voluntarily
participating in an industry program to collect and
recycle these batteries at the end of their useful
life, when taken out of service in the United States or Canada.
The RBRC program provides a convenient alternative to placing
used Ni-Cd batteries into the trash or the municipal waste
stream, which may be illegal in your area. Please call 1-800-
THE-SHACK (1-800-843-7422) for information on Ni-Cd battery
recycling and disposal bans/restrictions in your area.
RadioShack’s involvement in this program is part of the compa-
ny’s commitment to preserving our environment and conserving
our natural resources.
12
Preparation
43-1701.fm Page 13 Wednesday, September 20, 2000 8:48 AM
CONNECTING AND ADJUSTING THE
HEADSET
1. Insert the tabs on the headset holder
into the slots on the back of the base
and snap the holder into place.
2. Insert the headset’s plug into the jack
on the side of the keypad.
3. Place the headset on your head
with the earpiece over either ear.
4. Adjust the headset band until it
rests with almost no pressure
on your ear and the top of your
head.
5. If the headset is loose, press in slightly to tighten it. If it is
tight, gently pull the headset band out to loosen it.
6. Hold the headset in place and adjust the microphone boom
until it is about even with (but not in front of) your mouth.
Experiment until you find the most comfortable position.
Caution:
The microphone boom swivels on the headset. Do not
bend the microphone boom while you adjust it.
Note:
When you are not using the headset, place it on the
headset hanger. Otherwise (if you set it on a flat surface, for ex-
ample), you might have to repeat these adjustments.
13
Preparation
43-1701.fm Page 14 Wednesday, September 20, 2000 8:48 AM
SETTING RING/VIBRATE/DUAL
RING VIB
You can adjust the keypad’s ringer mode from
to
RING/VIB
.
VIB
With the ringer set to
when receiving call.
, the phone vibrates instead of ringing
RING/VIB
With the ringer set to
when receiving call.
, the phone rings and vibrates
Note:
The keypad does not vibrate when it is on the base.
TURNING THE RINGERS ON OR OFF
L1 RINGER OFF/ON
L2 RINGER OFF/ON
and
The keypad’s ringer
on the base control. To have the phone ring when a call comes
RINGER
ON
. To keep the phone
in, set
on the desired line to
RINGER
OFF
.
from ringing, set
on the desired line to
RINGER
OFF
, the phone does not ring for incoming
With
set to
calls, but you can still make outgoing calls. If you hear an exten-
sion telephone ring, you can answer the incoming call on this
phone. The L1 or L2 indicator flashes until you answer the call.
Note: RINGER
If
OFF
RING VIB RING/VIB
is set to
is set to
and
RING/VIB
, the keypad still vibrates when a call comes in.
VIB
or
SETTING THE DIALING MODE
TONE/PULSE
Set
on the side of the base for the type of service
you have. If you are not sure which type you have, do this sim-
ple test after charging the battery pack.
14
Preparation
43-1701.fm Page 15 Wednesday, September 20, 2000 8:48 AM
TONE/PULSE
TONE
.
1. Set
to
L2
so the indicator for that line lights and listen
L1
2. Press
or
for a dial tone.
3. Press any number other than or .
Note:
0
1
If your phone system requires that you dial an
access code (9, for example) before you dial an outside
number, do not press the access code either.
If the dial tone stops, you have touch-tone service. If the
dial tone continues, you have pulse service.
L1
L2
.
4. Press
or
TONE/PULSE
TONE
. If
.
5. If you have tone service, leave
you have pulse service, set
set to
TONE/PULSE
PULSE
to
Note:
Return the keypad to the base for at least 5 seconds after
you set the service type.
ˆ Operation
Before you use the phone, put the headset on and adjust it as
needed (see “Connecting and Adjusting the Headset” on
Page 13).
L1
L2
or . You hear a
To make a call, select a line by pressing
dial tone and the indicator for that line lights. Dial the number
you want to call.
15
Operation
43-1701.fm Page 16 Wednesday, September 20, 2000 8:48 AM
When you receive a call on a line, the light for that line flashes
and the phone rings or vibrates (if you set the ringer for that line
ON
to
). Press the button for the ringing line to answer the call.
The indicator for that line lights.
Notes:
• When you are using one line and a call comes on the other
line, the phone beeps or vibrates and the indicator of that
line flashes. You can hold the line you are using and
answer the call. (See “Using Hold” on Page 17.)
• When you press a button, a single tone indicates that the
phone has accepted the command. Three tones indicate
that you pressed a button in error or there is severe inter-
ference. (See “Changing Channels” on Page 18.)
• If interference is severe, the keypad might lose communi-
cation with the base and the call might disconnect. If this
happens, return the keypad to the base for about 5 sec-
onds to reset the security access-protection code.
ADJUSTING THE HEADSET’S VOLUME
VOLUME
To adjust the headset’s volume, repeatedly press
8
VOLUME
or
9 during a call until the sound level is comfortable.
You can set the headset’s volume to one of four levels, and it
remains set even after you hang up.
Note:
The keypad sounds 3 beeps when you reach the lowest
or highest listening level.
16
Operation
43-1701.fm Page 17 Wednesday, September 20, 2000 8:48 AM
USING HOLD
HOLD
lets you use the other line without disconnecting the call.
HOLD
You can alternate between the two lines by pressing
then the button for the desired line.
,
HOLD
1. To place a call on hold, press
line flashes.
. The indicator for that
2. To release a line from hold and continue your conversation,
press that line’s button.
Notes:
• If you press the other line’s button without first pressing
HOLD
, the first call is disconnected.
• If you hold the line for 1 minute, the keypad sounds
three beeps every 30 seconds. If you hold the line for 8
minutes, the keypad beeps for 2 minutes. Press that
line’s key to release the line from hold, or the line will be
automatically disconnected within 2 minutes. If you still
HOLD
want to hold the line, press
cycle.
again to repeat the
USING CONFERENCE
You can talk to both lines at the same time.
1. Use one line and hold the other line, or put both lines on
hold.
CONF
2. Press
. The indicators for both lines light.
17
Operation
43-1701.fm Page 18 Wednesday, September 20, 2000 8:48 AM
3. To hang up one line, press the other line’s key. Press the
key again to hang up both lines.
CHANGING CHANNELS
L1
L2
or , the phone automatically selects
Every time you press
a clear channel from the 10 it uses for communication between
the headset and the base.
CHAN-
If you hear interference during a call, repeatedly press
NEL
to change the channel until you get a clear one.
USING REDIAL
L1
L2
RE-
then
To quickly redial the last number dialed, press
or
DIAL/PAUSE
.
The redial memory holds up to 32 digits, so you can redial long-
distance as well as local numbers. The redial memory can also
store tone entries (see“Using Tone Services on a Pulse Line”
on Page 19) and pause entries (see “Entering a Pause in Mem-
ory Number” on Page 21).
REDIAL/PAUSE
If the number you dialed is busy, press
without
hanging up the phone to redial the number. The dial tone
sounds for about 2 seconds, then the phone redials the number.
USING MUTE
To talk to someone else in the room without the person on the
other end of the phone line hearing your conversation, press
MUTE
. The indicator for the line you are using flashes. Press
again to resume your phone conversation.
MUTE
18
Operation
43-1701.fm Page 19 Wednesday, September 20, 2000 8:48 AM
USING FLASH
FLASH
provides the electronic equivalent of a switchhook signal
for special phone services such as Call Waiting.
FLASH
For example, if you have Call Waiting, press
to answer
an incoming call without disconnecting the current call. Press
FLASH
again to return to the first call.
Note:
FLASH
If you do not have any special phone services, pressing
might disconnect your current call.
USING TONE SERVICES ON A PULSE LINE
Some special services, such as bank-by-phone, require tone
signals. If you have pulse service, you can still use these tone
services by following these steps.
1. Dial the service’s main number.
/TONE
2. When the service answers, press ∗
. Any additional
numbers you dial are sent as tone signals.
L1
L2
. The phone
3. After you complete the call, press
automatically resets to pulse dialing.
or
USING PAGE
You can send a page to the keypad to locate it when it is away
from the base and not in use.
PAGE
1. Press
on the base. The keypad rings for about 15
seconds.
19
Operation
43-1701.fm Page 20 Wednesday, September 20, 2000 8:48 AM
PAGE.
2. Press and hold
The keypad rings for about 1 minute.
PAGE
3. Press any key on the keypad or
silence it.
on the base to
MEMORY DIALING
You can store up to 10 numbers of up to 16 digits each in the
phone’s memory.
Notes:
• To keep your accounts secure, we recommend you do not
store your personal access code for services such as bank-
by-phone in a memory location.
• When storing numbers for special services (such as alter-
nate long-distance or bank-by-phone), store the service’s
main phone number in one memory location and numbers
for additional information in other locations.
Storing a Number in Memory
MEMORY
1. Press
on the keypad.
2. Enter the desired number (up to 16 digits).
MEMORY
3. Press
again.
1 0
4. Press the memory location ( – ). Two long beeps sound.
Note:
0
For the 10th memory location, press .
20
Operation
43-1701.fm Page 21 Wednesday, September 20, 2000 8:48 AM
5. You can write down the stored numbers on the memory
index card underneath the base.
Note:
If you hear three short beeps, you did not store the num-
ber successfully. Start again from Step 1.
Entering a Pause in Memory Number
In some telephone systems, you must dial an access code (9,
for example) and wait for a second dial tone before you can dial
an outside number. You can store the access code with the
phone number. However, if you do, you should also store a
pause after the access code to allow the outside line time to
REDIAL/PAUSE
connect. After entering the access code, press
to enter a 2-second pause.
Dialing a Stored Number
L1
L2
.
1. Press
or
MEMORY
2. When you hear the dial tone, press
, then the
1 0
memory location number ( – ). The phone dials the num-
ber.
Chain-Dialing Service Numbers
For quick recall of numbers for special services (such as alter-
nate long distance or bank by phone), store each group of num-
bers in its own memory location.
To call special services, dial the service’s main number. At the
MEMORY
appropriate place in the call, press
, then the number
for the location where the additional numbers are stored.
21
Operation
43-1701.fm Page 22 Wednesday, September 20, 2000 8:48 AM
Note:
If you use pulse dialing, be sure you have stored a tone
entry in another memory location (see “Using Tone Services on
a Pulse Line” on Page 19).
Testing Stored Emergency Numbers
If you store an emergency service’s number (police department,
fire department, ambulance) and you want to test the stored
number, make the test call during the late evening or early
morning to avoid peak demand periods. Remain on the line to
explain the reason for your call.
ˆ Troubleshooting
We do not expect you have any problem with your telephone,
but if you do, the following suggestions might help.
Problem
Suggestion
•
•
Move the keypad closer to the base. Raise the
base’s antenna to a vertical position.
Ensure the phone’s modular cord and the AC
adapter are correctly and securely connected.
The keypad
does not
work.
•
•
Recharge the keypad’s battery pack.
Reset the security access-protection code by plac-
ing the keypad on the base for about five seconds.
Keep the headset and base away from interference
sources such as computers, remote control toys, wire-
less alarm systems, wireless intercoms and room moni-
tors, fluorescent lights, and electrical appliances.
The call is
noisy.
22
Troubleshooting
43-1701.fm Page 23 Wednesday, September 20, 2000 8:48 AM
Problem
Suggestion
•
•
Turn off the interfering device.
There is
severe inter-
ference.
Move the keypad closer to the base. Hang up and
redial the number.
CHANNEL
to change the channel.
•
•
Press
Ensure the base’s antenna is raised and is not
touching a metal surface.
The range
decreases.
•
Recharge the keypad’s battery pack.
You can
TONE/PULSE
receive calls, Set
correctly for the type of service you
but cannot
make calls.
have (see “Setting the Dialing Mode” on Page 14).
If you still have problems, disconnect the phone. If other phones
on the same line work properly, the fault is in this phone or its
installation. If you cannot locate the problem, take your phone to
your local RadioShack store for assistance.
LIGHTNING
Your telephone has built-in lightning protection to reduce the
risk of damage from surges in telephone line and power line
current. This lightning protection meets or exceeds FCC re-
quirements. However, lightning striking the telephone or power
lines can damage your telephone.
Lightning damage is not common. Nevertheless, if you live in an
area that has severe electrical storms, we suggest that you un-
plug your phone before storms to reduce the possibility of dam-
age.
23
Troubleshooting
43-1701.fm Page 24 Wednesday, September 20, 2000 8:48 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and work-
manship under normal use for one (1) year from the date of purchase from RadioShack com-
pany-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS
PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PAR-
TICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN
LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY
OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE
CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR
ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED
TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROP-
ERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSE-
QUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusions may
not apply to you.
In the event of a product defect during the warranty period, take the product and the Ra-
dioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at
its option, unless otherwise provided by law: (a) correct the defect by product repair without
charge for parts and labor; (b) replace the product with one of the same or similar design; or (c)
refund the purchase price. All replaced parts and products, and products on which a refund is
made, become the property of RadioShack. New or reconditioned parts and products may be
used in the performance of warranty service. Repaired or replaced parts and products are war-
ranted for the remainder of the original warranty period. You will be charged for repair or re-
placement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God,
abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper
installation or maintenance, alteration, lightning or other incidence of excess voltage or current;
(b) any repairs other than those provided by a RadioShack Authorized Service Facility; (c) con-
sumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or in-
surance costs; or (f) costs of product removal, installation, set-up service adjustment or
reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
43-1701
RadioShack Corporation
Fort Worth, Texas 76102
08A00
Printed in China
|