12-1738.fm Page 1 Friday, January 7, 2000 9:07 AM
Cat. No. 12-1738
6- x 9-Inch 2 Way Flush-Mount Speaker System
CHOOSING A LOCATION
INSTALLING THE
SPEAKERS
For the best performance, install these
speakers on a solid, firm surface that
does not vibrate at high volume levels.
We recommend you mount the speak-
ers in the door panels or the rear
deck.
1. Use the supplied template to mark
the speaker opening and the
mounting-screw hole locations.
2. Cut out the marked speaker open-
ing in the mounting surface.
Note: Cardboard or fiber panels are
not good mounting surfaces.
Note: Steel door panels and the
rear deck (behind the upholstery)
might already have large cut-out
areas for recessing the speaker.
3. Drill the four mounting-screw
holes.
(illus showing suggested
mounting area.)
Caution: Be careful not to drill
into anything behind the mounting
surface.
4. If necessary, route new speaker
wire from the autosound system to
the mounting area.
As you are deciding on a location,
carefully inspect the area behind the
proposed mounting surface.
Cautions:
• There must be a clear unob-
structed area of at least 3 inches
(76.2 mm) behind the panel.
• Avoid routing speaker wires
near moving parts, sharp
edges, or where they will be
pinched or stepped on. You can
usually route them along the
channel beneath the vehicle’s
door facings.
• If it is a door location, check to be
sure the window, window mecha-
nism, and window handle will
clear the speaker.
Note: Make sure the window
opens and closes properly.
© 2000 Tandy Corporation.
All Rights Reserved.
RadioShack is a registered trademark used by Tandy Corporation.
12-1738.fm Page 3 Friday, January 7, 2000 9:07 AM
8. Align each speaker’s mounting
holes and mounting bracket’s
holes with the drilled holes on the
mounting surface and thread a
supplied screw through each hole.
10. Firmly press the grille onto each
speaker’s mounting bracket.
Note: You can use the supplied
adhesive putty tape to further
secure the grille to the mounting
bracket. Cut off and press a small
piece of putty into each of the four
9. Place one small and one large
washer and screw a nut onto the
mounting screw, then tighten all
screws until they are secure.
slots
around the mounting
bracket’s surface.
(illus
mounting
aligned
–
show the
screw,
with
the
(illus showing how to
use the putty)
speaker’s mounting
holes, the mounting
bracket’s holes, and
the fastening nuts)
3
12-1738.fm Page 4 Friday, January 7, 2000 9:07 AM
SPECIFICATIONS
Speaker Size:
Woofer ................................................................... 6 × 9 Inches (152 × 229 mm)
Tweeter ................................................................................. 21/2 Inches (64 mm)
Woofer, Cone .................................................................................... Paper Coating
Tweeter, Cone ................................................................................... Paper Coating
Grille ............................................................................................... Hi ABS Material
S.P.L. .............................................................................................................. 90 dB
Woofer Barium Magnet Weight ....................................................... 13.2 oz (375 g)
Tweeter Barium Magnet Weight .......................................................... 1.5 oz (43 g)
Power Handling .................................................................. 50 Watts RMS/Channel
Maximum Power.......................................................................... 150 Watts/Channel
Impedance ................................................................................................... 4 ohms
Frequency Response ........................................................................ 75 Hz–20 kHz
Weight (one speaker with grille) ................................................. 2 lb, 13 oz (1.3 kg)
Dimensions (HWD) ......................... 99/16 × 67/8 × 37/8 Inches (243 × 174 × 99 mm)
Specifications are typical; individual units might vary. Specifications are subject to
change and improvement without notice.
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety
(90) days from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees and dealers.
EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, IN-
CLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO
THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-
SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE
PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES
RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPE-
CIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequen-
tial damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase
date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product re-
pair without charge for parts and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or recon-
ditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are war-
ranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or
abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess
voltage or current; (b) any repairs other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation,
set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
01A00
Printed in China
|