Digital Wireless Speakers
RF-WS01/WS01-W/WS02
User Guide
Your RF-WS01, RF-WS01-W, or RF-WS02 Digital Wireless Speakers use
a proprietary 2.4GHz wireless communication system to transmit
low-latency, high fidelity audio from an audio source to wireless
speakers, providing a superior level of audio quality and resistance to
interference.
The system accepts line-level inputs, and is compatible with a
complete range of multi-channel home theatre systems or AV
receivers.
Safety information
CAUTION
Risk of Electric Shock
Do Not Open
This lightning flash with the arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
CAUTION
To reduce the risk of electric shock, do not remove the cover (or the
back). There are no user-serviceable parts inside. Refer servicing to
qualified service personnel.
Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to
rain or moisture.
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
RF-WS01/WS01-W/WS02
3
•
•
•
Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
•
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
•
•
Only use attachments or accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart and
apparatus combination to avoid injury from tip-over.
•
•
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
•
•
•
The apparatus shall not be exposed to dripping or splashing and no
objects with liquids such as vases, shall be placed on the apparatus.
The AC power adapter is used as the disconnect device. This disconnect
device shall remain readily operable.
Read the Rating labels on the bottom of the base station and wireless
speaker for power input and other safety information.
4
Features
•
•
•
•
•
2.4 GHz wireless sender and speaker
Transmits high quality audio over a radio frequency communication link
Compact size
Hidden antennas
Low power consumption
Package contents
Examine the contents of the box for your Rocketfish Digital Wireless
Speakers. The box should contain.
•
•
•
•
A sender unit
One speaker (RF-WS02) or two speakers (RF-WS01, and RF-WS01-W
An AC power adapter for the sender unit
One (RF-WS02) or two (RF-WS01 and RF-WS01-W) AC power adapter(s)
for the speakers
•
A User Guide
Sender
The sender transmits audio signals over a 2.4 GHz radio frequency
carrier to the speaker.
RF-WS01/WS01-W/WS02
5
Front view
1
Item Description
1
Power and link Status LED—GREEN
Side view
1
Item Description
1
Power ON/OFF switch with Status LED
6
Back view
1
2 3
Item Description
1
2
3
RCA audio input terminals
DC IN jack
Pairing (manual connect) button
Speaker
The speaker receives the 2.4 GHz audio signals from the sender and
plays out the sound using the built-in amplifier and speakers. The
speaker can operate from the supplied AC adapter or from batteries.
RF-WS01/WS01-W/WS02
7
Front (RF-WS01/RF-WS01-W)
1
2
3
Item Description
1
2
3
Power ON/OFF switch with Status LED
Volume control
Left/Mono/Right control
8
Back (RF-WS01/RF-WS01-W)
1
2
Item Description
1
2
DC IN jack
Pairing (manual connect) button
RF-WS01/WS01-W/WS02
9
Front (RF-WS02)
1
2
4
5
6
3
7
Item Description
1
LED:
•
•
•
•
Solid green—Connected to AC power
Quick flashing—Pairing mode
Slow flashing—No link
Red—Low battery
2
3
Bass Boost LED—RED
Charging LED:
•
•
Flashing green—Charging
Solid green—Charging complete
4
5
6
7
Power ON/OFF switch
Bass Boost control button
Speaker output selector (Left/Mono/Right) switch
Volume control
10
Back (RF-WS02)
1
2
Item Description
1
2
Pairing (manual connect) button
DC IN jack
RF-WS01/WS01-W/WS02
11
Setting up your system
Caution: Turn off your audio source while connecting the units
Connecting the sender
To connect the sender to an audio source:
1
Connect a stereo RCA cable from an audio source to the sender taking
care to match white and red colors at both ends. Make sure that the
cable is connected to an audio source and not a video source.
To right and
left input jack
To right and left
output jack
2
Connect the AC adapter connector to the sender DC IN jack.
Caution: To avoid risk of fire, and to prevent damage, only use the AC adapter
supplied with your digital wireless speakers. Make sure that power supply outlet
matches the AC adapter’s 120V before making the connection.
Plug the AC power
adapter in only after
your audio source is
connected to the
sender.
DC IN 5V
12
Connecting the speakers
Plug the AC power adapter in if batteries are not being used or if the
batteries are discharged.
Caution: To avoid risk of fire, and to prevent damage, only use the AC adapter
supplied with your digital wireless speakers. Make sure that power supply outlet
matches the AC adapter’s 120V before making the connection.
To connect the AC adapter to your speakers:
•
Connect the AC adapter connector to the speaker DC IN jack.
RF-WS01 & RF-WS01-W
RF-WS02
RF-WS01/WS01-W/WS02
13
Installing batteries into the speakers
Caution: Do not mix battery types. Do not use old and new batteries together.
Remove all batteries if the unit is not going to be used for a long period of time.
1
2
With the speaker AC adapter disconnected, open the battery cover.
Install eight (8) C size batteries taking care to follow the battery polarity
markings on the battery compartment.
3
For WS-02, set the Alkaline/NiMH battery switch to the type of C size
batteries being used. The switch is inside the battery compartment. Use
the Alkaline setting if you are using standard non-rechargeable alkaline
batteries. Use the NiMH setting if you are using rechargeable NiMH
batteries.
4
Replace the battery cover. When charging (speakers on or off), the LED
flashes green slowly. When charging is complete, the LED lights solid
green. If the LED flashes green quickly, the charger cannot charge the
batteries. Replace the batteries with new ones. Full battery charging can
take up to 24 hours.
Warning: Do not try to recharge alkaline batteries. Use C size NiMH rechargeable
batteries. Failure to do so may damage the speakers or cause a fire. The speaker will
try to charge batteries if the battery switch is set to NiMH.
Note: Rechargeable batteries can be recharged with the speakers on or off. RF-WS-01
and RF-WS-01-W cannot recharge any type of batteries. If you want to use
rechargeable batteries in the RF-WS-01 or RF-WS-01-W, you must use a regular
standalone charger to recharge batteries.
Positioning the speakers
Caution: To avoid the risk of electric shock and fire, and to prevent damage, locate
the sender and speakers with no obstructions in front of the ventilation holes.
Caution: Do not use the WS-01 or WS-03 in a wet environment. If you use the WS-02
outdoors or in wet environment, do not connect the AC adapter.
Note: if you need to mount the speakers, make sure that the left and right speakers
are switched to the correct left, right, or mono setting for speaker output sound.
Note: For best performance, the sender LED should face the general direction of the
area where you plan to place the speakers.
14
Using your system
Turning on your system
To turn on the system:
1
Move the Power switch to the ON position on the side panel of the
sender. The green Link Status LED starts to blink slowly to indicate the
sender is plugged in and in Standby mode.
2
Press the Power switch on the front panel of the speakers. The green
Status LED starts to flash to indicate the receiver is plugged in and in
Standby mode.
Note: If the speaker is operated by batteries and battery capacity is too low to power
the speakers, the Low Battery Warning LED turns red to indicate a low battery
warning.
The sender and speakers were pre-paired in the factory. When an active
link is established between them the green Link Status LEDs turn solid.
Note: If the LEDs continue to blink after 30 seconds, it means there is no active link
between the sender and speakers. Try to connect the system manually using the PAIR
button. For more information see “Troubleshooting” on page 17.
Listening to your system
To listen to the system:
1
Turn on the system. Make sure that there is an active link between the
sender and speakers. When an active link is established between them
the green Link Status LEDs turn solid.
2
Turn on your audio source, then play the audio.
To adjust the volume on the RF-WS01 or RF-WS01-W:
•
Turn the volume knob on the speaker. The volume is adjusted
independently regardless of channel setting (left, right, or mono).
To adjust the volume on the RF-WS02:
•
Turn the volume knob on the speaker. Make sure the speaker is switched
to the correct left, right, or mono setting for speaker output sound.
RF-WS01/WS01-W/WS02
15
Turning off the system
To turn off the system:
1
Move the sender Power switch to the OFF position. The Green Link
Status LED goes off indicating that the sender is turned off.
2
Push the Power switch on the front panel of each speaker. The Green
Link Status Power LED goes off to indicate that the speaker is turned off.
Speaker auto shut-off on RF-WS02 speakers
When the speakers are running on battery power, they turn off
automatically when the device they are connected to is turned off or
does not send audio for more than five minutes. This feature
conserves battery life.
Optimizing your surround sound
Your Rocketfish digital wireless speakers use state-of-the-art 2.4 GHz
technology to digitally send audio data from the sender to the
speakers. Wireless links create a small latency between the sender
and receiver, and many A/V receivers let you adjust the delay
between various speakers in your surround system. If using
Rocketfish digital wireless speakers as part of a surround system, you
can optimize your system when tuning your speaker setup by
shortening the delay to the wireless speakers by 15-20ms.
Low Battery warning
The red Low Battery Warning LED is lit when there is no AC power
and the battery capacity is not enough to power the speaker. Replace
the old batteries with fresh Alkaline batteries, or charge your
rechargeable batteries.
Using Bass Boost (RF-WS02 only)
Bass Boost enhances the low-end sound. If the Bass Boost button is
pressed once, the unit enters Bass Boost mode, and the red Bass
Boost LED is lit. If the Bass Boost button is pressed again, the unit
exits Bass Boost mode and the red Bass Boost LED turns off.
16
Maintaining your system
Use a soft cloth dampened with a weak solution of mild detergent
and water. Dry the apparatus immediately afterwards with a clean
cloth. Do not use abrasive cloth, thinners, alcohol, or other chemical
solvents, because they may damage the finish or remove the panel
lettering.
Cautions:
•
Do not cover the ventilation openings with items, such as newspapers,
table clothes, and curtains.
•
If the power cord is damaged, it must be repaired by a qualified repairer.
Note:
If the RS-WS02 becomes wet, you can drain water by gently tipping it
slightly to one side for a few seconds.
•
Troubleshooting
Read this User Guide carefully before using your digital wireless
speakers. Check this list for a possible troubleshooting solution
before calling for service.
Problem
Solution
No sound
•
Make sure the sender AC adapter is connected to the sender, and either the
speaker AC adapter is connected or fresh or charged batteries are installed
in the speakers.
•
Make sure that all cables are connected correctly. Check to see if the green
Link Status LEDs illuminate on the front of both the sender and speaker
units. If the green Link Status LEDs are lit solidly, the communication is
working correctly and the audio cables from audio source to the sender
should be checked. If the green Link Status LEDs are flashing or off, refer to
the “No communication between sender and speaker” section below.
RF-WS01/WS01-W/WS02
17
Problem
Solution
Sound interference
•
•
•
Move your sender and speaker slowly to find the best reception position for
your system.
Shorten the distance to between your sender and speakers. The maximum
distance is 55 feet (RF-WS01 or RF-WS01-W) or 100 feet (RF-WS02).
Check to determine if there are any obvious radio frequency interference
sources near your system.
No communication
between the sender
and speaker
•
•
Make sure that the power cords and/or batteries are connected or installed
correctly.
After the power switch is ON position and turn on both the sender and
speaker, the front panel green Link Status LEDs should light. If they are lit
solidly on, a communication link has been established between the units. If
they are flashing or off on any of the units, press and hold the PAIR button
on either the sender or speakers for more than three seconds. (The sender's
and speakers PAIR buttons are located on rear panel of unit.) This will put
the unit into “connection mode” for about 30 seconds. During this period
the PAIR button on the other units must also be pressed for more than three
seconds so that it will also enter “connection mode”. The system proceeds
with the connection process between sender and speaker. While in
“connection mode”, the green Link Status LEDs blink at a faster rate. When
an active link is established between the sender and receiver, the LEDs will
be solid on and will not blink.
Note: Try pressing the PAIR buttons again if the green Link Status LEDs keep
blinking after 30 seconds.
Specifications
Sender
Audio Input: Stereo, line level Maximum 1Vrms or 2Vrms
Audio Output: Wireless
•
•
•
Stereo, 48 kHz uncompressed
Bit-rate: 2.465 Mbps
Raw wireless bit-rate: 2Mbps
Supply Voltage
Transmission Delay
5V @ 200mA
15-20mS
18
Speakers (RF-WS01 and RF-WS01-W)
Audio Input: Wireless
•
•
•
Stereo, 48 kHz uncompressed
Bit-rate: 1.465 Mbps
Raw wireless bit-rate: 2Mbps
Audio Output
•
•
8W (RMS) 2-way speaker full range system (10% THD)
High Efficiency Class D speaker amplifier driving internal full range speakers
Supply Voltage
Power Consumption
Transmission Delay
12V @ 1.0A
12W
15-20mS
Speakers (RF-WS02)
Audio Input: Wireless
•
•
•
Stereo, 48 kHz uncompressed
Bit-rate: 1.465 Mbps
Raw wireless bit-rate: 2Mbps
Audio Output
•
•
20W (RMS) bi-amp speaker full range system (10% THD)
High Efficiency Class D speaker amplifier driving internal full range speakers
Supply Voltage
Power Consumption
Transmission Delay
15V @ 1.2A
18W
15-20mS
Legal notices
FCC Part 15 [short version--keep?]
This device complies with Part 15 of the FCC Rules. Operation of this
product is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
RF-WS01/WS01-W/WS02
19
This equipment has been tested and found to comply within the
limits for a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced technician for help.
FCC warning
Changes or modifications not expressly approved by the party
responsible for compliance with the FCC Rules could void the user’s
authority to operate this equipment.
IC RSS210 STATEMENT
Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
Canada ICES-003 statement
This Class B digital apparatus complies with Canadian ICES-003.
20
Information for Users on Disposal of Old Equipment
[European Union]
Note: This symbol is only valid in the European Union.
This symbol indicates that the electrical and electronic
equipment should not be disposed as general household
waste at its end-of-life. Instead, the product should be handed
over to the applicable collection point for the recycling in accordance
with your national legislation.
By disposing of this product correctly, you will help to conserve
natural resources and will help prevent potential negative effects on
the environment and human health that could otherwise be caused
by inappropriate waste handling of this product. For more
information about collection point and recycling of this product,
please contact your local municipal office, your household waste
disposal service or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in
accordance with national legislation.
[Other Countries Outside the European Union]
If you wish to dispose of this product, please do so in accordance
with applicable national legislation or other rules in your country for
the treatment of old electrical and electronic equipment.
RF-WS01/WS01-W/WS02
21
One-Year Limited Warranty
Rocketfish Products (“Rocketfish”) warrants to you, the original purchaser of this new
RF-WS01/RF-WS01-W/WS02 (“Product”), that the Product shall be free of defects in the
original manufacture of the material or workmanship for one (1) year from the purchase of the
Product (“Warranty Period”). This Product must be purchased from an authorized dealer of
Rocketfish brand products and packaged with this warranty statement. This warranty does not
cover refurbished Product. If you notify Rocketfish during the Warranty Period of a defect
covered by this warranty that requires service, terms of this warranty apply.
How long does the coverage last?
The Warranty Period lasts for one year (365 days), beginning on the date you purchased the
Product. The purchase date is printed on the receipt you received with the product.
What does this warranty cover?
During the Warranty Period, if the original manufacture of the material or workmanship of the
Product is determined to be defective by an authorized Rocketfish repair center or store
personnel, Rocketfish will (at its sole option): (1) repair the Product with new or rebuilt parts; or
(2) replace the Product at no charge with new or rebuilt comparable products or parts. Products
and parts replaced under this warranty become the property of Rocketfish and are not returned
to you. If service of Products and parts are required after the Warranty Period expires, you must
pay all labor and parts charges. This warranty lasts as long as you own your Rocketfish Product
during the Warranty Period. Warranty coverage terminates if you sell or otherwise transfer the
Product.
How to obtain warranty service?
If you purchased the Product at a retail store location, take your original receipt and the Product
to the store you purchased it from. Make sure that you place the Product in its original
packaging or packaging that provides the same amount of protection as the original
packaging. If you purchased the Product from an online web site, mail your original receipt and
the Product to the address listed on the web site. Make sure that you put the Product in its
original packaging or packaging that provides the same amount of protection as the original
packaging.
Where is the warranty valid?
This warranty is valid only to the original purchaser of the Product in the United States, Canada,
and Mexico.
What does the warranty not cover?
This warranty does not cover:
•
•
•
•
Customer instruction
Installation
Set up adjustments
Cosmetic damage
RF-WS01/WS01-W/WS02
23
•
•
•
•
•
•
•
Damage due to acts of God, such as lightning strikes
Accident
Misuse
Abuse
Negligence
Commercial use
Modification of any part of the Product, including the antenna
This warranty also does not cover:
•
•
•
Damage due to incorrect operation or maintenance
Connection to an incorrect voltage supply
Attempted repair by anyone other than a facility authorized by Rocketfish to service the
Product
•
•
•
Products sold as is or with all faults
Consumables, such as fuses or batteries
Products where the factory applied serial number has been altered or removed
REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY.
ROCKETFISH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT
NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST
PROFITS. ROCKETFISH PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES WITH RESPECT TO
THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING, BUT
NOT LIMITED TO, ANY IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD
SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER
THE WARRANTY PERIOD. SOME STATES, PROVINCES AND JURISDICTIONS DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.
Contact Rocketfish:
For customer service please call 1-800-620-2790
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, Minnesota, U.S.A. 55423-3645
© 2008 Best Buy Enterprise Services, Inc.
All rights reserved. ROCKETFISH is a trademark of Best Buy Enterprise Services, Inc. Registered in
some countries. All other products and brand names are trademarks of their respective owners.
24
(800) 620-2790
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN 55423-3645 USA
© 2008 Best Buy Enterprise Services, Inc.
All rights reserved. ROCKETFISH is a trademark of Best Buy Enterprise Services, Inc.
All other products and brand names are trademarks of their respective owners.
ENGLISH
08-1669
|
