C a s p i a n
5-CH AMPLIFIER
5 - C h a n n e l A/ V P ow er Amp l i f i e r
U S E R M A N U A L
R O K S A N A U D I O L I M I T E D
6 NORTHFIELD INDUSTRIAL ESTATE
BERESFORD AVENUE
MIDDLESEX HA0 1NW
ALPERTON
ENGLAND
T E L .
F A X .
+ 4 4 ( 0 ) 2 0 8 9 0 0 6 8 0 1
+ 4 4 ( 0 ) 2 0 8 9 0 0 6 8 0 2
+ 4 4 ( 0 ) 2 0 8 9 0 0 0 7 3 4
CAUTIONS
C a s p i a n 5-Ch Amplifier
AC MAINS SUPPLY
Your Caspian 5-Channel Power Amplifier is set to operate from a fixed supply voltage which is marked on a label
next to the mains input plug. Before connecting the mains lead please check that your mains supply corresponds
to this label as below:
230V Products ………………………………….Voltage Range: 220V – 240V
115V Products ………………………………….Voltage Range: 100V – 120V
100V Products ………………………………….Voltage Range: 90V – 110V
The mains lead supplied with this product has an IEC mains socket which plugs into the IEC connector on the
unit’s rear panel. The other end is normally attached to the appropriate mains plug for your country. In the UK
this is the standard UK13A plug.
This plug should ordinarily not be removed from the lead. If you do remove it, please dispose of it safely so that it
cannot be plugged into a mains socket whilst in a potentially dangerous condition. We suggest that you obtain
from your dealer a complete replacement lead.
Should you move to another area where either the mains voltage or the mains plugs are different from those as
supplied with your 5-Channel Power Amplifier, please contact the appointed ROKSAN distributor for assistance.
Please observe correct mains polarity at all times.
The 5-Channel Power Amplifier mains fuse is located on the rear panel next to the IEC mains connector. This
must only be replaced by the fuse of the type and rating as described on the fuse rating label on the rear panel of
the unit.
This product requires connection to earth (ground). The earth wire (in the UK this is colour coded green/yellow)
of the mains cable supplied with your 5-Channel Power Amplifier must be connected to a suitable earthing point
established for this purpose by your electricity supply company. If you are in any doubt, consult a qualified
electrician.
If the equipment is likely to be unused for some time, unplug it from the mains supply.
GENERAL CAUTIONS
FCC WARNING
This equipment may generate or use Radio Frequency energy. The user may lose the right to operate this
equipment if unauthorised modifications are made.
INTERFERENCE
Properly installed, this unit should not cause harmful interference to radio communications, There is, however, no
guarantee that such interference will not occur in a specific installation. If interference arises (which you can
determine by switching the unit off and on) you could try to remedy matters by the following:
•
•
•
•
Re-orient or re-locate the receiving antenna
Increase the distance between the 5-Channel Power Amplifier and receiver
Connect the unit to a different mains circuit from that of the receiver
Consult your ROKSAN appointed dealer or an experienced Radio/TV technician for help and advice
LOCATION
Your Caspian 5-Channel Power Amplifier should be located in a well ventilated area and kept away from sources
of heat, dust and humidity and from direct sunlight.
The 5-Channel Power Amplifier may be positioned either as a free standing unit or alongside another audio/video
product. Never place the 5-Channel Power Amplifier on carpet or any surface likely to hinder normal ventilation.
Never allow liquids or other objects to fall into the unit.
This unit contains no user serviceable parts. Do Not remove any panels or attempt to service it yourself.
Unauthorised servicing will void the warranty.
Roksan Audio ltd
Caspian 5-Channel A/V Power Amplifier User Manual
CLASSIFICATION: General Use
Version 2.01
All specifications are liable to change without notice. E&OE
Page 3 of 9
ENGLISH
INSTALLATION
C a s p i a n 5-Ch Amplifier
ROKSAN Caspian 5-Channel Power Amplifier- Front Panel View
1
2
3
4
5
6
7
8
9
MODE
CH 1
CH 3
CH 2
CH 4
CH 5
AUTO
MODE
MODE
R O K S A N
5-Channel A/V Amplifier
C a s p i a n
1. Standby / On Button
2. Standby Indicator
3. Channel 1 Overload Indicator
4. Channel 2 Overload Indicator
5. Channel 3 Overload Indicator
6. Channel 4 Overload Indicator
7. Channel 5 Overload Indicator
8. Auto / Operation Indicator
9. Standby / On Button
ROKSAN Caspian 5-Channel Power Amplifier - Rear Panel View
5a
4a
3a
2a
1a
5
4
3
2
1
6
C H AN N EL5
C H AN N EL4
C H AN N EL3
C H AN N EL2
C H AN N EL1
AC IN PU T
WARN IN G
C H A I N
C H A I N
C H A I N
C H A I N
C H A I N
REFER T O O W N ERS MAN U AL FOR CO RREC T IN STALLATION
IN STRUCTIO NS. DO NO T O PERATE T HIS PRO DUCT WITH IT S
CO VERS REMOVED. DO NO T EXPOSE THIS PRO DUCT TO
MOISTURE. DO NO T AT TEMPT TO GAIN ACCESSTO THEINSIDE
O F THIS UNIT. REFER ALL SERVICING T O ROKSAN APPRO VED
AN D QUALIFIED PERSON NEL O NLY.
O U T PU T
T U P I N
IN PU T
O U T P U T
T U P I N
IN PU T
O U T P U T
T U P I N
IN PU T
O U T P U T
T U P I N
IN PU T
O U T P U T
T U P I N
IN PU T
SR
SL
FR
FL
C
5-CH AN N EL A/V AM PLIFIER
S
E
R
I
A
L
N
U
M
B
E
R
IM P O RTA N T
SPEA KER O U T PU T
SPEA KER O U T PU T
SPEA KER O U T PU T
SPEA KER O U T PU T
SPEA KER O U T PU T
1b
5b
4b
3b
2b
8
7
Roksan Audio ltd
Caspian 5-Channel A/V Power Amplifier User Manual
CLASSIFICATION: General Use
Version 2.01
All specifications are liable to change without notice. E&OE
Page 4 of 9
ENGLISH
1. Channel 1 Input
1a. Channel 1 Chain Signal Output
1b. Channel 1 Loudspeaker Output
2. Channel 2 Input
2a. Channel 2 Chain Signal Output
2b. Channel 2 Loudspeaker Output
3. Channel 3 Input
3a. Channel 3 Chain Signal Output
3b. Channel 3 Loudspeaker Output
4. Channel 4 Input
4a. Channel 4 Chain Signal Output
4b. Channel 4 Loudspeaker Output
5. Channel 5 Input
5a. Channel 5 Chain Signal Output
5b. Channel 5 Loudspeaker Output
6. Mains Power Switch
7. Mains Power Fuse Holder
8. Mains Power Connector
SETUP
C a s p i a n 5-Ch Amplifier
CONNECTING MAINS POWER
Please refer to rear panel view on Page 4. The moulded IEC connector of the supplied mains lead should be
plugged into the socket 8 on the rear of the unit first and then plugged into the mains supply. The Mains power
switch 6 is on the rear panel of the 5-Channel Power Amplifier. This switch is normally left on. If the unit is likely
to be unattended for a long period, switch it off and unplug the mains lead from the wall.
SIGNAL CONNECTIONS
Signal Inputs:
There are 5 Analogue Inputs with Gold plated RCA Phono Sockets and connections are
made as follows:
Front Left Channel Input
Front Right Channel Input
Centre Channel Input
Surround Left Channel Input
Surround Right Channel Input
1
2
3
4
5
(FL) White
(FR) Red
(C) Green
(SL) Blue
(SR) Blue
Connect to Front Left Channel output of Surround Sound Processor
Connect to Front Right Channel output of Surround Sound Processor
Connect to Centre Channel output of Surround Sound Processor
Connect to Surround Left Channel output of Surround Sound Processor
Connect to Surround Right Channel output of Surround Sound Processor
Signal Outputs:
There are 5 Analogue Chain Outputs with Gold plated RCA Phono Sockets and connections
are made as follows:
Front Left Channel Chain Output
Front Right Channel Chain Output
Centre Channel Chain Output
1a (FL) White
2a (FR) Red
3a (C) Green
Surround Left Channel Chain Output 4a (SL) Blue
Surround Right Channel Chain Output 5a (SR) Blue
These outputs are used for Multi-Amping the Loudspeakers. Connect the ‘Chain’ Output to another Input of the
5-Channel Power Amplifier* or an Input of another 5-Channel Power Amplifier for Bi-Amping (or Tri-Amping etc.)
of your Loudspeakers for improved performance.
* when the Main or the Centre or the Surround speakers are driven from another amplifier.
IMPORTANT NOTE: For optimum performance it is recommended to use high quality inter-connect cables such
as ROKSAN HDC-02A high definition analogue Cable.
Roksan Audio ltd
Caspian 5-Channel A/V Power Amplifier User Manual
CLASSIFICATION: General Use
Version 2.01
All specifications are liable to change without notice. E&OE
Page 5 of 9
ENGLISH
OUTPUT CONNECTIONS
Speaker Outputs: Your Caspian 5-Channel Power Amplifier has 5 Gold plated Loudspeaker Terminals and
connections are made as follows:
Front Left Channel Output
Front Right Channel Output
Centre Channel Output
Surround Left Channel Output
Surround Right Channel Output
1b (FL) Red (+)
2b (FR) Red (+)
3b (C) Green (+)
4b (SL) Blue (+)
5b (SR) Blue (+)
Black (-)
Black (-)
Black (-)
Connect to Front Left Channel Speaker
Connect to Front Right Channel Speaker
Connect to Centre Channel Speaker
Black (-) Connect to Surround Left Channel Speaker
Black (-) Connect to Surround Left Channel Speaker
The loudspeakers are connected to the amplifier via the rear panel binding posts, 1b, 2b, 3b, 4b and 5b.
Remove any overall sheath or split figure 8 cable to a depth of about 75mm (3 "). Strip the insulation round each
conductor to a depth of 12mm (½ "). If the cable is stranded, twist the strands together. Unscrew the binding
posts. Insert the bare ends through the holes. Tighten ensuring no bare wires are visible.
Ensure that you connect the RED (+) speaker terminal to the RED or GREEN or BLUE (+) amplifier terminal and
the BLACK (-) speaker terminal to the BLACK (-) amplifier terminal.
IMPORTANT NOTE: For optimum performance it is recommended to use high quality cables such as ROKSAN
HDC-01S high definition Loudspeaker Cable. Many speaker cables such as the ROKSAN HDC-01S are
directional. Please observe this directionality. DO NOT use speaker cable with conductor size less than 16 AWG
(1.6mm Diameter). The Binding posts accept conductor sizes up to 12 AWG and most ¼" Spade connectors.
Bi- Amped Speaker
Using another channel
of the same 5-Channel
Power Amplifier
Bi- Wiring
Note links
removed
Bi- Amped Speaker
Using another
Standard Wiring
Note links between
Speaker Drive Unit
Terminals
5-Channel Power
Amplifier
Note links
removed
F
R
F
L
F
R
FL
C
C
HF
HF
HF
HF
HF
LF
HF
LF
LF
LF
LF
LF
Connect to Front Right output
of Caspian DSP Surround
Sound Processor
Connect to Front Left
output of Processor
Connect to
Front Left output of Processor
Front Right output
Of Processor
A
C
I
N
P
U
T
A
C
I
N
P U
W
A
R
N
I
N
G
W
A
R
N
I
N
G
RE F E R
T
O
O
W
N
ERS
RE F E R
T
O
O
W
N
ERS
M AN U AL FO R C O RREC T
M AN U AL FO R C O RRC T
I
N
S
T
A
L
L
A
T
I
O
N
I
N
S
T
A
L
L
A
I
N
SR
SL
FR
FL
SR
SL
FR
FL
C
C
S
E
R
I
A
L
N
U
M
T
B
R
E
R
I
A
L
N
U
M
T
B
E
R
I
M
P
O
R
A
N
T
I
M
P
O
R
A
N
T
S
P
E
A
K
E
R
S
P
E
A
K
E
R
S
P
E
A
K
E
R
S
P
E
A
K
E
R
S
P
E
A
K
E
R
S
P
E
A
K
E
R
S
P
E
A
K
E
R
S
P
E
A
K
E
R
P
E
A
K
E
R
P
E
A
K
E
R
A
C
I
N
P U
W
A
R
N
I
N
G
S
R
SL
RE F E R
T
O
O
W
N
ERS
AN U AL FO R C O RREC T
I
N
T
A
L
L
A
T
I
O
N
SR
SL
C
FR
FL
HF
LF
HF
LF
S
E
R
I
A
L
N
U
M
T
B
E
R
I
M
P
O
R
A
N
T
S
P
E
A
K
E
R
S
P
E
A
K
E
R
S
P
E
A
K
E
R
S
P
E
A
K
E
R
S
P
E
A
K
E
R
SR
SL
HF
LF
HF
LF
Roksan Audio ltd
Caspian 5-Channel A/V Power Amplifier User Manual
CLASSIFICATION: General Use
Version 2.01
All specifications are liable to change without notice. E&OE
Page 6 of 9
ENGLISH
OPERATION
C a s p i a n 5-Ch Amplifier
Please refer to the front panel view on page 4.
After connection to the Mains supply, switch the Caspian 5-Channel Power Amplifier ON at the rear panel. It will
enter STANDBY and the STANDBY LIGHT (2) glows RED. Press either of the MODE buttons (1 or 9), after a
couple of seconds, the amplifier will set it self in AUTO mode and the AUTO LIGHT (8) will glow GREEN and the
STANDBY LIGHT (2) will extinguish. Your Caspian 5-Channel A/V Power amplifier is now ready for use.
To set the amplifier back into standby, press either of the MODE buttons (1 or 9), and the AUTO LIGHT will
extinguish and the STANDBY LIGHT (2) glows RED.
Thanks to its advance circuit design and 1 kVA power transformer, the Caspian 5-Channel Power amplifier is
capable of audiophile sound quality with excellent transient power to compliment both ‘pure audio’ and
audio/visual sound tracks. Your Caspian 5-Channel power amplifier is a high power, high current amplifier with
very low distortion.
Most of the time, even with the most demanding material, it will not current limit and the distortion will remain
ultra low. However when using low impedance loudspeakers at very high volume levels or when the surround
sound processor output is set too high, the amplifier may occasionally current limit and its output distortion begin
to increase. The control circuit of your 5-Channel Power Amplifier will automatically detect this and on the front
panel display the corresponding channels’ Overload Indicator (3, 4, 5, 6 or 7) will glow RED. You should first
check the output of level of your surround sound processor and if it is set too high Trim it lower. Secondly lower
the Master Volume and if applicable consider Multi-Amping your loudspeakers.
IMPORTANT NOTE: The current Overload Indicators will only illuminate if the amplifier is driven continuously at
or past its maximum current capacity. These indicate overload of the power supply just before the onset of
audible distortion. These Indicators in virtually all imaginable listening situations will rarely illuminate
The control circuit indicates a fault when one or more of the Overload Indicators glow continuously RED without
any input signal. You should switch the amplifier immediately off and contact your ROKSAN Authorized Retailer.
Multi-Amping The Loudspeakers
Operation
If the Loudspeakers utilise more than one drive unit with individual input terminals, for example a Tweeter and a
Woofer, then the loudspeaker performance will benefit from Bi-Amping. Dedicating one amplifier to the Tweeter
and another to the Woofer, isolates them from each other hence reducing distortion and increasing reserved
power. Speakers work far better with most amplifiers when Multi-Amped than using one yet more powerful
amplifier. Note: Bi-Wiring reduces the impedance seen by the Woofer and the Tweeter and is a first step towards
Bi-Amping.
TROUBLESHOOTING
C a s p i a n 5-Ch Amplifier
If you suspect that your ROKSAN Caspian 5-Channel Power Amplifier is not operating properly, you should
check all the connections carefully. Below are some commonly encountered problems with suggestions for
possible cure. The list is not exhaustive: If you have any unresolved problems, please consult your appointed
ROKSAN dealer or distributor.
SYMPTOM
LIKELY CAUSE
SUGGESTED REMEDY
No power
AC Mains lead not inserted properly
Ensure AC Mains lead is fully inserted
Unit not switched on at rear panel
Switch unit on at rear panel
No output on one or more
channels
Amplifier in stand-by mode (MODE light Press MODE button to set amplifier in
RED)
AUTO mode (AUTO light GREEN)
Check all input connections
Check all output connections on rear
panel
Missing or bad input signal connection
Incorrect speaker connection
Over heating
Allow amplifier to cool, increase
ventillation or use at lower volume
Check Mains polarity and grounding on
all connected equipment
Hum from speakers
Incorrect Grounding
Roksan Audio ltd
Caspian 5-Channel A/V Power Amplifier User Manual
CLASSIFICATION: General Use
Version 2.01
All specifications are liable to change without notice. E&OE
Page 7 of 9
ENGLISH
GUARANTEE
C a s p i a n 5-Ch Amplifier
There are no user-serviceable parts inside your Caspian 5-Channel A/V Power Amplifier. If a fault should
develop, refer any servicing to your appointed ROKSAN dealer, distributor or ROKSAN approved service agent.
Your ROKSAN Caspian 5-Channel A/V Power Amplifier is guaranteed against any defect in materials and
workmanship for a period of two years from the date of purchase.
This guarantee only becomes effective if the warranty card is validated by the ROKSAN retailer from whom the
equipment was purchased and returned to ROKSAN within 28 days of purchase.
This guarantee excludes:
1. Damage caused due to accident, missuse, neglect and incorrect installation, adjustment or repair.
2. Liability for damage or loss during transit from the retailer or purchaser to ROKSAN or its authorised
distributor for the purposes of repair or inspection.
Carriage costs to ROKSAN shall be borne by the consignor.
All claims under this guarantee must be made through an authorised ROKSAN retailer.
If equipment returned for repair to ROKSAN is found on inspection to comply with the product specification
ROKSAN reserves the right to make a charge for examination and return carriage.
Unauthorised servicing will void this guarantee.
SPECIFICATIONS
C a s p i a n 5-Ch Amplifier
No. of Inputs
5 Signal Inputs (FR, FL, C, SR and SL)
Input Impedance
Input Sensitivity
No. of Outputs
33 kΩ
900mV
5 Signal Chain Outputs (FR, FL, C, SR and SL)
5 Speaker Outputs (FR, FL, C, SR and SL)
Output Power
>85 Watts into 8 Ohms,
>125 Watts into 8 Ohms,
>125 Watts into 4 Ohms,
>210 Watts into 4 Ohms,
all channels driven
2-channels driven
all channels driven
2-channels driven
Current Output
>35 Amps Peak to Peak
>105V / µSecond
-3dB, 3Hz – 110kHz
1KHz, >80 dB
Slew Rate
Frequency response
Separation
Harmonic Distortion
I M Distortion
<0.003% on all outputs
<0.02% on all outputs
JISA 50 µV
Maximum Hum and Noise
Signal to Noise Ratio
Power Source
JISA >105 dB
100V – 120V 50Hz / 60Hz
220V – 240V 50Hz / 60Hz
Power Consumption
Dimension
< 1000 W
432 x 430 x 140 (W x D x H) mm
432 x 430 x 150 (including feet)
Weigth
25 Kg
Roksan Audio ltd
Caspian 5-Channel A/V Power Amplifier User Manual
CLASSIFICATION: General Use
Version 2.01
All specifications are liable to change without notice. E&OE
Page 8 of 9
ENGLISH
NOTES
C a s p i a n 5-Ch Amplifier
Caspian 5-Channel A/V Power Amplifier
Serial Number: …………………………
Year .……… Month …….. Day ……..
Purchase Date
ROKSAN Retailer
Name:
…………………………………
Location: ………………………………
Please keep a record for future reference
Roksan Audio ltd
Caspian 5-Channel A/V Power Amplifier User Manual
CLASSIFICATION: General Use
Version 2.01
All specifications are liable to change without notice. E&OE
Page 9 of 9
ENGLISH
|